Warner-electric Autogap 825-1225 Uživatelský manuál stáhnout pdf

Autogap Installation for

Sizes 825-1225 Motor Brakes

Installation Instructions

P-1375

819-0081

Assembling the Armature and Hub

Assemble the armature to the armature hub with

the autogap mounting accessory. Follow these

instructions to assemble the armature and hub.

1. Apply Loctite

#242 (or #290, or equivalent) to

drive pin threads. Insert the drive pin into the hub

and tighten until the shoulder of the pin is against

the hub. (Figure 1)

2. Assemble the red

spring over the drive

pin. The smaller

diameter of the

spring should be

against the hub.

3. Place the detent

retainer over the

pin. The cupped-

out portion should

be against the

spring. (Figure 2)

4. Place the detent ring

on the pin and press it into the recessed portion

of the detent retainer. (Figure 2)

5. Slide the detent ring

towards the hub to

allow about 1/2"

between the ring

and head of the pin.

(Figure 3)

6. Slide the armature on

the pins. The face of

the armature should

be towards the hub.

Figure 3

7. Assemble the light spring over the pin. The large

diameter of the spring should be against the

Hub Red Spring

Drive Pin

armature. (Figure 4)

8. Compress the spring

to allow the retainer

ring to be snapped

into the groove at the

head of the pin.

Mounting the Armature-Hub Assembly

(See Figure 5)

1. Insert taperlock bushing into the bore of the hub.

2. Loosely insert the locking setscrews and slide the

assembly on to the shaft.

3. Position the assembly to allow a gap of 1/16"

between the faces of the armature and magnet.

4. Secure the assembly in this position by alternately

tightening the locking setscrews. The bushing should

be tapped lightly from time-to-time to make sure it

seats-in properly.

5. Set the autogap by

pressing the armature

into contact with the

friction face and then

releasing the

armature. The

armature should

spring back

approximately 1/32".

Once this gap is set it

will be automatically

maintained throughout

the life of the unit.

6. Use capscrews and

lockwashers to bolt

adapter cover.

Red SpringHub

Drive Pin

Detent Retainer

Detent

Ring

Ligh

Spri

Armature

Hub

Armature

Drive Pin

Light Spring

Retainer Ring

0.062

(1.57)

Capscrew

Adapter

Armature

Hub

Magnet

Detent Spring Retainer

Figure 5

Retainer

Ring

Drive

Light

Spring

Detent

Retainer

Detent

Ring

Red

Spring

Hub

Armature

Failure to follow

these instructions may result in

product damage, equipment

damage, and serious or fatal injury

to personnel.

Figure 1

Figure 2

Figure 4

Warner Electric 800-825-9050

1 2

Shrnutí obsahu

Strany 1 - Sizes 825-1225 Motor Brakes

Autogap Installation for Sizes 825-1225 Motor BrakesInstallation InstructionsP-1375819-0081Assembling the Armature and HubAssemble the armature to the

Strany 2 - Warranty

WarrantyWarner Electric LLC warrants that it will repair or replace (whichever it deems advisable) any product manufactured and sold by it which prove

Komentáře k této Příručce

Žádné komentáře

Warner-electric Autogap 825-1225 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Warner-electric Autogap 825-1225. Warner Electric Autogap 825-1225 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Hardware Warner-electric Autogap 825-1225